The DEMOQE128 is a low-cost development system designed for demonstrating, evaluating, and debugging the Freescale MC9S08QE128 and MCF51QE128 microcontrollers. It's Multilink circuitry on the DEMOQE128 board allows the processor on the DEMOQE128 to be debugged and programmed via USB from the PC. In addition, the demo board can be powered using the USB bus.
Supports S08 and ColdFire V1 QE128 devices through plug-in daughter cards. It also supports plug-in RF daughter cards for SMAC and 802.15.4.
FEATURES
On-board logic analyzer
On-board virtual serial port
Asymmetrically positioned 4 8x2 male connectors for interchangeable daughter cards
P&E's embedded multilink circuitry populated on the bottom
RS-232 serial port w/ DB9-F connector
SCI signals connected to P&E's embedded multilink through jumpers
ON/OFF power switch w/ LED indicator
A 5V DC to 12V DC power supply input barrel connector
Power input selection jumpers for selecting the input voltage source:
Power input from embedded multilink to LDO regulator
INPUT_EN for two input channels to embedded multilink
SPECIFICATIONS
Board Size 3.5 x 4.0
Power Input:
USB Cable: 5VDC, 500mA max
DC Power Jack: 2.5/5.5mm barrel connector,
5VDC to 12VDC Center Positive
Two AAA Battery Cells
DEMOQE DAUGHTER CARD FEATURES
Built-in BDM eliminates need for external BDM cable
Four bottom-mounted asymmetrically positioned 8x2 female connectors to mate with the DEMOQE base board a top-mounted MC9S08QE128CLH or MCF51QE128CLH chip
One RS232 COM port plus optional SCI via USB
Virtual logic analyzer through two TPM channels via USB
Three-axis accelerometer
Operates from battery pack with two “AAA” batteries
KIT CONTAINS
DEMOQE base board with a MC9S08QE128 Daughter Card installed
MCF51QE128 Daughter Card
DVD Breaking Bit Boundaries
Getting Started With QE128
2-cell AAA battery package
USB cable
Quick Start Guide
Freescale warranty card
Flexis QE128 Evaluation Board
The EVBQE128 evaluation board has been designed for the evaluation, demonstration and debugging of the Freescale Flexis QE128 microcontrollers (MC9S08QE128 and MCF51QE128). The EVBQE128 can be used as a standalone application or can be controlled by a host PC via its built-in microDART™ interface.
FEATURES
An “MCU” section containing:
An 80-pin LQFP socket accepting either the MC9S08QE128 or the MCF51QE128 microcontroller
A crystal oscillator, a provision for a clock module, a provision for a connector for providing an external clock source, together with jumpers to select the clock source
A BDM connector for in-circuit debugging/programming with an external instrument
A female header connectors with all of the MCU signals
A power supply section containing:
A 12V DC barrel input connector (2.1mm)
A four-way micro terminal block for providing specific power supplies and voltage references to the microcontroller
A jumper to select the power supply source (USB bus or barrel connector)
A power on/off switch
A built-in “microDART INTERFACE” section (with the main circuitry mounted on the back of the board) which allows the host PC to communicate with the microcontroller through a standard USB interface. Jumpers are present to configure this module. Thanks to the microDART in-circuit debugging firmware, BDM commands are sent to the target microcontroller through the USB bus. Additionally, a virtual COM port is automatically available over the same USB connection. This virtual COM port can be used by standard terminal programs, like HyperTerminal, to send/receive serial characters to/from the target microcontroller.
An “I/O” section containing
A Reset push-button
Four additional push-button
One potentiometer
Eight dip-switches
A piezoelectric buzzer
A light sensor
A temperature sensor
Ten user LEDs
A circuitry for driving and external LCD
A series of jumpers to connect/disconnect the above controls to/from the microcontroller
An “RS-232” section containing two RS-232 connectors together with a jumper to enable the RS-232 communication
A “SERIAL SETTINGS” section containing jumpers to select communication options
KIT CONTAINS
The EVBQE128 evaluation board
80-pin LQFP MC9S08QE128 and MCF51QE128 microcontrollers
A USB cable
A pick-up vacuum pump
A universal, 12V DC power supply
System software DVD-ROM, including CodeWarrior™ Development Studio
Previous Page
Previous Page