How to Design a Precise Infrared Motion Sensor at Low Cost

By Tomas Knatterod, Field Applications Engineer, Future Electronics (Norway)

READ THIS TO FIND OUT ABOUT High accuracy infrared sensor design Industrial control systems Sensor-array optimization

Designers of industrial equipment can produce a robust and precise IR motion detector at far lower cost than commercial off-the-shelf versions.

Motion sensing is commonly used in a variety of industrial and security applications. Precision motion sensors can often be found in products such as industrial process equipment, vending machines and recycling sorters.

Highly precise commercial off-the-shelf motion sensors can be found on the market today for such applications, but they are extremely expensive. If more than 50 units of such equipment are to be built, it will generally be cheaper to design a precision motion sensor using components that are freely available from broadline distributors such as Future Electronics.

There is a wide choice of technologies available for creating a new motion sensor, and each offers a different combination of cost and performance for different applications. Of all of them, Infrared (IR) sensor technology usually offers the lowest cost solution. This article will focus on the best way to design a precision IR motion sensor for industrial applications.

Before starting the design of a motion detector, it is important to analyze certain key factors about the object to be detected and its environment:

• Speed of the object (max/min)
• Size of the object (the largest and smallest two-dimensional area that the detector must monitor)
• Distance from the object to the sensor (max/min)
• Presence of other sources of IR radiation in the detection area (such as human beings or animals) apart from the object to be detected
• Presence of objects or buildings in or near to the detection area that could reflect IR radiation

The presence of other sources of IR radiation can be a critical problem. At best, this will complicate the design; at worst, it can make the use of an IR sensor completely impossible.

In this case, the designer should either consider alternative sensing technologies, or take other measures to stop unwanted sources of IR radiation from intruding into the detection area. Similarly, the presence of objects that could reflect IR radiation on to a PIR sensor could prevent its use, or require complex and difficult signal processing routines to be developed to filter out reflected radiation. In a typical industrial application, such as a conveyor belt in a factory, however, these complications do not arise.

The Basic Structure of an IR Sensor for Motion Detection

There are three ways to configure an IR motion detector:

1. With the transmitters on one side of the detection area and the receivers on the other side (see Figure 1)
2. With both the detectors and receivers on one side of the detection area and a reflector on the other side (see Figure 2)
3. With a transmitter and a receiver on one side of the detection area and no reflector, so that radiation only reaches the receiver when reflected from an object (see Figure 3)

The third configuration described above can only be used in a system with just one receiver and transmitter. Such a system is not capable of the accurate and precise sensing of motion, and is more appropriate for intruder alarms.

In order to design a precision motion detector, it is important to know the smallest size of the objects to be detected. This is because the IR transmitters have to sit slightly closer to each other than the smallest possible length of object to be detected. Knowing this variable, and the width of the detection area, it is easy to calculate how many IR transceivers are needed:

This formula is valid for motion detector systems both with receivers and transceivers on the same side of the object to be detected and with receivers and transceivers opposite each other.

 

How the System Works

All the receivers are connected to the same ADC. The system switches the transmitters in sequence, and if a receiver detects no signal when its transmitter ‘pair’ is active, the system knows that an object is in the detection area (see Figure 4).

The reason for switching each transmitter in sequence is that this allows them to be driven at peak current, maximizing IR output intensity. In continuous mode, an IR LED typically operates at 65mA forward current, but in peak mode forward current can be as much as 1A. In order to maximize the allowable distance between the transmitter and receiver, then, it is necessary to run the IR LEDs in peak current mode.

 

Peak mode is shown in the datasheet for most IR LEDs with specified ratings for pulse width (typically up to 100µs) and duty cycle (typically up to 1%).

It is important to know the maximum speed of the object to be detected, because this determines the minimum switching time of the LEDs. The formula below can be used to calculate this minimum switching time. It can be seen from the formula that when more LEDs are used, the switching frequency increases:

The application of both formulae can be shown using the following example, based on detecting boxes passing on a conveyor belt, where the short side of the box is 17mm long and where the detection area is 7.5cm x 50cm. The motion detector is positioned so as to detect the shortest side of the box. The conveyor belt’s maximum speed is 5m/s.

Calculating the number of LEDs and transmitters:

Therefore the system requires 6 LEDs and 6 receivers.

Calculating the LED switching time:

Therefore the LED switching time in this example will be 566µs.

As the formula shows, the required switching frequency can be uncomfortably high if a small object is moving at speed. This has important ramifications for the selection of the microcontroller. In particular, it is important to choose a microcontroller with a high MIPS rating if the LED switching frequency is high. This is because it is often necessary to perform some signal processing functions on the analog input signals between each LED switching operation.

If the switching time is below 2ms, a 32-bit processor is recommended to handle signal processing functions. STMicroelectronics’ new STM32 device uses ARM’s Cortex core and offers sufficient processing performance to suit these high frequency applications. NXP’s ARM7 and STMicroelectronics’ STR7 series of 32-bit microcontrollers could also be considered.

 

 

Cost vs. Performance

The most cost efficient configuration for this IR motion detector is to place the receivers and the transistors on the same side of the PCB (see Figure 2), but this adds complication.

In this configuration, IR light needs to be emitted in a straight line through the detection area, and not scattered outside this line. Any stray light risks being reflected to a receiver that the transmitter is not paired with.

Z-bend surface mounted LEDs are useful in this situation. The Z-bend package is back-mounted, which makes it possible to use the PCB itself to narrow the angle of the IR light coming out of the transmitter. This also provides for robust mechanical design, eliminating the need for a glass or acrylic protective cover.

It is important that the phototransistor receives no light directly from its paired LED and only receives light from the reflector. When an LED emits light through a hole in the PCB, light can pass through the fibers in board material. It is therefore necessary to metal plate the holes in which the LEDs are mounted, and it may be prudent to do the same for the phototransistor holes.

Phototransistors and IR LEDs are often supplied in pairs, where the phototransistor is optimized for the corresponding LED. Fairchild Semiconductor, Avago Technologies and Vishay are leading producers of these components.

 

 

Almost all the light from an LED goes in a forward direction, at an angle specified by the manufacturer, but some of the light also comes out from the side. This means that it is necessary to isolate the sides of the LED and phototransistor if they are placed close together.

This can be difficult to accomplish. One method commonly adopted is to vacuum mount a silicon material that is resistant to IR light around the phototransistor and the LED. Practical experience, however, suggests that the LED’s forward light output changes in terms of the angle and intensity when a silicon material is in contact with it. Mounting an isolator that is made of a different material is one way around this problem.

The choice of reflector also significantly impacts the performance of the system. Broadly, the greater the distance between the transmitter and the reflector, the better the specification of the reflector must be. For practical purposes, the maximum size of detection area is around 1m across when using a reflector.

A higher resolution reflector and better reflector material will significantly improve the performance of the system. Reflector tape has the advantage of low cost, but much better performance is achieved using a good industrial plastic reflector in demanding applications. However, if the detection distance is less than 40cm, reflector tape is often good enough.

It is obvious, then, that the design of a system with one PCB (transmitters and receivers on the same side of the detection area) is cheap, but requires significant trade-offs to be accommodated in the design.

The alternative configuration, shown in Figure 2, with two PCBs and the transmitters and receivers on opposite sides of the detection area, avoids these complications, but results in a higher bill of materials. As well as being simpler to design, the twoboard approach also makes it easy to extend the distance between the receivers and transmitters up to several meters.

When using this two-board configuration, it is possible to run the system with one microcontroller. This, however, requires a large number of cables to connect the LEDs and phototransistors, and heightens the risk of noise distorting the signal. For this reason, it is better to implement this particular configuration with two microcontrollers: one to control the transmitters and one to control the receiving phototransistors. Then the system only requires a single synchronization signal between the two microcontrollers, eliminating the need for multiple cables.

 

The Environment Around the Detection Area

Ideally, no objects will be positioned close to the detection area. An object near the detection area could create blind spots for the receivers. To avoid this, any objects that cannot be removed from the detection zone should be coated with anti-reflective matte paint.

Sunlight and other light sources also often contain IR light. This can create unwanted noise that can cause detection failures. It is possible to write software routines to calibrate for sunlight error. This technique involves filtering out slow IR detection events (because changes in sunlight generally occur slowly), and only register fast movements in the detection area. Even this, however, is not perfect, because sunlight and other light sources can flash or create sudden shadows in certain situations.

 

Conclusion

By using simple components (LEDs, phototransistors and a microcontroller) and the careful component mounting techniques described in this article, it is possible for designers of industrial equipment to produce a robust and precise IR motion detector at far lower cost than commercial off-the-shelf versions.